ArcGIS 10.0 SP2 (Desktop, Engine, Server) Topology Validation Patch

This patch addresses an issue where exception geometry becomes corrupted during topology validation. Esri recommends that all topology users apply this patch.

Esri® announces the ArcGIS 10.0 SP2 (Desktop, Engine, Server) Topology Validation Patch. This patch addresses an issue where exception geometry becomes corrupted during topology validation. It deals specifically with the issues listed below under Issues Addressed with this Patch.

Issues Addressed with this Patch

NIM067085 - Validating topology returns “Validate Topology Failed”. A failure was detected inside the topology engine overlay processor, [error id: 109].
Description: When validating topology containing errors that have been marked as exceptions, the geometry of the exceptions may become corrupted. Attempting to validate the topology over these exceptions will fail with the message: “A failure was detected inside the topology engine overlay processor, [error id: 109]”. Underlying features are not affected by this issue. If you have encountered this error message, find corrupted exception shapes, or have any exceptions in your topology, you should follow the post installation instructions after installing this patch.

Files Installed in this Patch

Under the Windows <ArcGIS Product Installation Directory>\bin folder:
- ExtTopoEngine.dll

Under the Linux/Solaris <ArcGIS Product Installation Directory>/bin folder:
- ExtTopoEngine.dll

Installing this Patch on Windows

Installation Notes:

System Administrators - A technical paper is available that discusses the enterprise deployment of ArcGIS 10 setups using Microsoft® Systems Management Server (SMS) and Group Policy, including additional system requirements, suggestions, known issues, and Microsoft Software Installation (MSI) command line parameters. Deployment in a lockdown environment is also covered. ArcGIS 10 Enterprise Deployment.

ArcGIS 10 Service Pack 2 Desktop, Engine, Reader or Server must be installed before you can install this patch.

Download the appropriate file to a location other than your ArcGIS installation location.

ArcGIS Desktop	Gis10sp2-DT-TV-Patch.msp

ArcGIS Engine	Gis10sp2-E-TV-Patch.msp

ArcReader	Gis10sp2-R-TV-Patch.msp

ArcGIS Server - Gis Services	Gis10sp2-SGIS-TV-Patch.msp

ArcGIS Server Java	Gis10sp2-SJ-TV-Patch.msp

Make sure you have write access to your ArcGIS installation location.
For ArcGIS Server for the Microsoft .NET Framework Only: Open the Services Management Console> Control Panel > Administrative Tools > Services. Stop the ArcGIS Server Object Manager and ArcGIS Server SOC Monitor services.

For ArcGIS Server Java Only: Open the Services Management Console> Control Panel > Administrative Tools > Services. Stop the ArcGIS Server Object Manager; ArcGIS Server SOC Monitor and ArcGIS Server Manager services.
Double-click Gis10sp2-<Product>-TV-Patch.msp to start the install process.

NOTE: If double clicking on the MSP file does not start the Patch installation, you can start the Patch installation manually by using the following command:
- msiexec.exe /p [location of Patch]\Gis10sp2-<Product>-TV-Patch.msp
When Setup starts, follow the instructions on your screen. At the end of the installation, follow the instructions to run the GIS Server Post Install.
For ArcGIS Server for the Microsoft .NET Framework Only: Open the Services Management Console> Control Panel > Administrative Tools > Services. Start the ArcGIS Server Object Manager and ArcGIS Server SOC Monitor services.

For ArcGIS Server Java Only: Open the Services Management Console> Control Panel > Administrative Tools > Services. Start the ArcGIS Server Object Manager; ArcGIS Server SOC Monitor and ArcGIS Server Manager services.
Post Installation Instructions:
If you have encountered the error message in the description, find corrupted exception shapes, or have any exceptions in your topology, you need to modify the topology after installing the patch to ensure the topology is usable again. Since this issue only affects topologies that have exceptions, right-click the topology in the Catalog window, click Properties, click the Errors tab, and click Generate Summary to see a report of rules and their errors and exceptions. If there are exceptions in your topology, click the Rules tab and remove any rule containing an exception. You can leave the topology rules without exceptions intact. After you validate the topology, add the removed rules again. In some cases, it may be easier to delete the topology altogether and add the rules into a new topology. When the rules are removed, any previous exceptions will need to be re-marked as exceptions when you are editing the topology.

Installing this Patch on Linux and Solaris

Complete the following install steps as the ArcGIS Install owner. The Install owner is the owner of the arcgis folder.

ArcGIS 10.0 Service Pack 2 Engine, Reader or Server must be installed before you can install this Patch.

Download the appropriate file to a location other than your ArcGIS installation location.

ArcGIS Engine for Linux	Gis10sp2-E-TV-Patch-linux.tar

ArcGIS Engine for Solaris	Gis10sp2-E-TV-Patch-slrs.tar

ArcGIS Reader for Linux	Gis10sp2-R-TV-Patch-linux.tar

ArcGIS Reader for Solaris	Gis10sp2-R-TV-Patch-slrs.tar

ArcGIS Server for Linux	Gis10sp2-S-TV-Patch-linux.tar

ArcGIS Server for Solaris	Gis10sp2-S-TV-Patch-slrs.tar

Make sure you have write access to your ArcGIS installation location, and that no one is using ArcGIS.
For ArcGIS Server only: stop the ArcGIS server by typing:
% arcgis/scripts/stopserver
Extract the specified tar file by typing:
% tar -xvf Gis10sp2-E-TV-Patch-linux.tar (Linux)
% tar -xvf Gis10sp2-E-TV-Patch-slrs.tar (Sun Solaris)
% tar -xvf Gis10sp2-R-TV-Patch-linux.tar (Linux)
% tar -xvf Gis10sp2-R-TV-Patch-slrs.tar (Sun Solaris)
% tar -xvf Gis10sp2-S-TV-Patch-linux.tar (Linux)
% tar -xvf Gis10sp2-S-TV-Patch-slrs.tar (Sun Solaris)
Start the installation by typing:
% ./applypatch
This will start the dialog for the menu-driven installation procedure. Default selections are noted in parentheses ( ). To quit the installation procedure, type 'q' at any time.
For ArcGIS Server only: start the ArcGIS Server by typing:
- % arcgis/scripts/startserver

Patch Updates

Check the ArcGIS Resource Center periodically for the availability of additional patches. New information about this Patch will be posted here.

How to identify which Patch is installed

Windows

To find out what ArcGIS products are currently installed on your machine, download the PatchFinder.exe utility and run it from your local machine.

Linux / Unix

To find out what ArcGIS products are currently installed on your machine, download and extract the PatchFinder utility and run it from your local machine.

Getting Help

Domestic sites, please contact Esri Technical Support at 1-888-377-4575, if you have any difficulty installing this Patch. International sites, please contact your local Esri software distributor.

Download ID:1776