Patches and updates

ArcGIS Server 10.8.1 Geoprocessing Service Orphaned Process Patch

Published: October 15, 2020

Summary

This patch resolves an issue where geoprocessing services published from ArcGIS Pro, including print services, can leave orphaned processes leading to high memory usage.

Description

Esri® announces the ArcGIS Server 10.8.1 Geoprocessing Service Orphaned Process Patch. In certain scenarios a geoprocessing service executing a job that exceeds the timeout set on the service can fail to unload its process after completing. This causes orphaned processes to be left behind that consume memory and which will not be cleaned up until a reboot of the machine. It is recommended that this patch is installed on all machines in ArcGIS Server sites used for geoprocessing including both out-of-the-box and custom print services. This patch deals specifically with the issues listed below under Issues Addressed with this patch.

 

Issues Addressed with this patch

 

  • BUG-000134547 - ArcGIS Server geoprocessing services, such as print services, can leave orphaned processes leading to high memory usage.

 

Installing this patch on Windows

 

Installation Steps:

 

This patch should be installed on all ArcGIS Server installations related to the ArcGIS Server site.

The ArcGIS product listed in the table must be installed on your system before you can install a patch. Each patch setup is specific to the ArcGIS product in the list. To determine which products are installed on your system, please see the How to identify which ArcGIS products are installed section. Esri recommends that you install the patch for each product that is on your system.

  1. Download the appropriate file to a location other than your ArcGIS installation location.

    ArcGIS 10.8.1   Checksum (Md5)
         
        ArcGIS Server ArcGIS-1081-S-GSOP-Patch.msp 152EA48A7EA221D6708C44127190BE23
         

  2. Make sure you have write access to your ArcGIS installation location.
  3. Double-click ArcGIS-1081-S-GSOP-Patch.msp to start the setup process.

    NOTE: If double clicking on the MSP file does not start the setup installation, you can start the setup installation manually by using the following command:

    msiexec.exe /p [location of Patch]\ArcGIS-1081-S-GSOP-Patch.msp

 

Installing this patch on Linux

 

Installation Steps:

 

Complete the following install steps as the ArcGIS Install owner. The Install owner is the owner of the arcgis folder. This patch should be installed on all ArcGIS Server installations related to the ArcGIS Server site.

The ArcGIS product listed in the table must be installed on your system before you can install a patch. Each patch setup is specific to the ArcGIS product in the list. To determine which products are installed on your system, please see the How to identify which ArcGIS products are installed section. Esri recommends that you install the patch for each product that is on your system.

  1. Download the appropriate file to a location other than your ArcGIS installation location.


    ArcGIS 10.8.1   Checksum (Md5)
         
        ArcGIS Server ArcGIS-1081-S-GSOP-Patch-linux.tar 780CA720456E49D75385EFD11D3106E6
         

  2. Make sure you have write access to your ArcGIS installation location, and that no one is using ArcGIS.
  3. Extract the specified tar file by typing:

    % tar -xvf ArcGIS-1081-S-GSOP-Patch-linux.tar
     
  4. Start the installation by typing:

    % ./applypatch

    This will start the dialog for the menu-driven installation procedure. Default selections are noted in parentheses ( ). To quit the installation procedure, type 'q' at any time.

Uninstalling this patch on Windows

 

To uninstall this patch on Windows, open the Windows Control Panel and navigate to installed programs. Make sure that "View installed updates" (upper left side of the Programs and Features dialog) is active. Select the patch name from the programs list and click Uninstall to remove the patch.

 

Uninstalling this patch on Linux

 

Uninstalling on Linux is only available on version 10.5.1 or higher. These instructions are specific to 10.7 and higher. To remove this patch, navigate to the <Product Installation Directory>/.Setup/qfe folder and run the following script as the ArcGIS Install owner:


./removepatch.sh

The removepatch.sh script allows you to uninstall previously installed patches or hot fixes. Use the -s status flag to get the list of installed patches or hot fixes ordered by date. Use the -q flag to remove patches or hot fixes in reverse chronological order by date they were installed. Type removepatch -h for usage help.

 

Patch Updates

Check the Patches and Service Packs page periodically for the availability of additional patches. New information about this patch will be posted here.

 

How to identify which ArcGIS products are installed

To determine which ArcGIS products are installed, choose the appropriate version of the PatchFinder utility for your environment and run it from your local machine. PatchFinder will list all products, hot fixes, and patches installed on your local machine.

Getting Help

Domestic sites, please contact Esri Technical Support at 1-888-377-4575, if you have any difficulty installing this patch. International sites, please contact your local Esri software distributor.


Download ID:7840

Get help from ArcGIS experts

Contact technical support

Download the Esri Support App

Go to download options