Patches and updates

ArcGIS 10.2 Web Adaptor (IIS) .NET 4 Support and Trust Patch

Published: September 6, 2013

Summary

This optional patch provides support for Microsoft .NET 4.x with the IIS Web Adaptor. The Web Adaptor can now be configured to target .NET version 4.0 application pools in IIS when previously, only .NET version 2.0 application pools were supported. This patch also addresses an issue where the Web Adaptor could only communicate with ArcGIS for Server when the Microsoft .NET Trust Level of the Web Adaptor application was set to a level of Full (Internal).

Description

EsriĀ® announces the ArcGIS Web Adaptor (IIS) .NET 4 Support and Trust Patch. This patch provides support for Microsoft .NET Framework 4.0 and 4.5, plus .NET Trust support for the High and Medium levels with the IIS Web Adaptor. It deals specifically with the issues listed below under Issues Addressed with this Patch.

.NET Framework 4 Support

The Web Adaptor can now be configured to target .NET version 4.0 application pools in IIS when previously, only .NET version 2.0 application pools were supported.

To take advantage of this patch after installing it, you will first need to install .NET Framework Version 4.0 or 4.5.

Next, you will change the version of the Web Adaptor application pool from version 2.0 to 4.0 following these steps:

  1. Open Internet Information Systems (IIS) Manager.
  2. In the Connections pane, click Application Pools.
  3. Right-click the ArcGISWebAdaptorAppPool application and select Advanced Settings.
  4. In the General section, change the .NET Framework Version to v4.0.
  5. Click OK.

High and Medium Trust Level Support

The Web Adaptor can now optionally be used with a Microsoft .NET Trust Level of High or Medium for those customers that have this security requirement.

Full Trust continues to be required when initially configuring the Web Adaptor with ArcGIS for Server and Portal for ArcGIS. Once configured, the Web Adaptor can then be changed to use a .NET Trust Level of High or Medium from that point forward.

To take advantage of this patch after installing it, temporarily set the Trust level of the Web Adaptor application to Full in IIS. (If the trust level assigned to the Web Adaptor is set to High or Medium when opening the configuration page, you'll see an error message stating that Full Trust is temporarily required. If the trust is set to Low or Minimal, the configuration page will fail to open. Again, a Trust level of Full is temporarily required.) The steps to modify this in IIS are:

  1. Open Internet Information Systems (IIS) Manager.
  2. In the Connections pane, click Sites.
  3. Select the Web Adaptor application you want to configure.
  4. Double-click the .NET Trust Levels icon.
  5. Select Full (internal) in the Trust Level dropdown.
  6. Click Apply in the Actions pane.

Next, configure the Web Adaptor with your ArcGIS Server or Portal for ArcGIS.

To finish, set the .NET Trust Level of the Web Adaptor to High or Medium and proceed with having client applications send requests through the Web Adaptor.

Additional Help

For full discussion of .NET Trust Levels, see the following topics in the ArcGIS Web Adaptor (IIS) installation guide:

 

Issues Addressed with this Patch

  • NIM085761 - Update the IIS Web Adaptor to support .NET Framework 4.x.
  •  
  • NIM089344 - IIS Web Adaptor throws a security exception when .NET Trust Level is set to any value other than Full (Internal) trust.

 

Files Installed in this Patch

Under the <IIS web site\web adaptor name> folder:
  • App_GlobalResources\webAdaptor.resx
    webadaptor\WebAdaptor.aspx
    Web.config
Under the c:\windows\assembly folder:
  • ESRI.ArcGIS.WebAdaptor.dll

 

Installing this Patch on Windows

Installation Steps:

ArcGIS 10.2 Web Adaptor (IIS) must be installed before you can install this patch.

  1. Download the appropriate file to a location other than your ArcGIS installation location.

        Checksum (Md5)
    ArcGIS Web Adaptor (IIS) ArcGIS-102-WAI-N4ST-Patch.msp 48700C2660B6C78C6960A689B81DD3F0

  2. Make sure you have write access to your ArcGIS installation location.
  3. Double-click ArcGIS-102-WAI-N4ST-Patch.msp to start the install process.

    NOTE: If double clicking on the MSP file does not start the setup installation, you can start the setup installation manually by using the following command:

    msiexec.exe /p [location of Patch]\ArcGIS-102-WAI-N4ST-Patch.msp

Installation Notes:

While installing the patch, IIS will be restarted and resources accessed through the Web Adaptor will be temporarily unavailable.

If a machine has multiple IIS Web Adaptors installed on it, launching the patch will trigger the installation wizard to run once for each Installed Web Adaptor. You will need to click the Update and Finish buttons for each Web Adaptor being updated.

After applying the patch to a Web Adaptor, you may choose to install additional Web Adaptors. Installing additional Web Adaptors will require applying the patch again. Until the patch is applied again, opening the configuration page for a new Web Adaptor will fail with an IIS error.

After applying the patch, you do not need to open the configuration page to register the Web Adaptor again.

Patch Updates

Check the Patches and Service Packs page periodically for the availability of additional patches. New information about this patch will be posted here.

 

How to identify which ArcGIS products are installed

To determine which ArcGIS products are installed, choose the appropriate version of the PatchFinder utility for your environment and run it from your local machine. PatchFinder will list all products, hot fixes, and patches installed on your local machine.

  • PatchFinder for Windows

Getting Help

Domestic sites, please contact Esri Technical Support at 1-888-377-4575, if you have any difficulty installing this patch. International sites, please contact your local Esri software distributor.



Download ID:2011

Get help from ArcGIS experts

Contact technical support

Download the Esri Support App

Go to download options